The second method, which we have called diagonal bridging, is more effective in preventing the partition from sagging than is the straight bridging, but both methods may be used with equal pro priety. In the diagonal bridging the short pieces are set in diagonally, as is shown in Fig. 127, instead of horizontally, between the vertical studding. This method is certainly more scientific than the other, since a continuous truss is formed across the wall.
All partitions should be bridged by one of these methods, at least once in the height of each story, and the bridging pieces should be securely nailed to the vertical studding at both ends. It is cus tomary to specify two tenpenny nails in each end of each piece. Bridging should be placed in the exterior walls as well as in the partition walls; and as a further precaution against fire, it is good practice to lay three or four courses of brickwork, in mortar, on the top of the bridging in all walls, to prevent the fire from gaining head way in the wall before burning through and being discovered. This construction is shown in Fig. 12S.
Special Partitions. A partition in which there is a sliding door must be made double to provide a space into which the door may slide when it is open. This is done by building two walls far enough apart to allow the door to slide in between them, the studding being of 2 X 4-inch or 2 X 3-inch stuff, and placed either flatwise or edgewise in the wall. If the studding is placed flat wise in the wall a thinner wall is possible, but the construction is not so good as in the case where the studs are placed edge wise. If the partition is to sup port a floor, one wall must be made at least 4 inches thick to support it, and the studs in the other wall may then be placed flatwise if desired, and the floor supported entirely on the thick wall. The general arrangement is shown in plan in Fig. 129. It is better to use 2 X 4-inch studding set edgewise in each wall so as to make two 3-inch walls with space enough between to allow the door to slide freely after the pocket has been lined with sheathing.
A piece of studding A, Fig. 130, should be cut in hori
zontally between each pair of studs B, S or 10 inches above the top of the door in order to keep the pocket true and square. The pocket should be lined on the inside with matched sheathing C.
It is well known that ordinary partitions are very good con ductors of sound; and in certain cases, as in tenement houses, this is objectionable, so that special construction is required. If two walls are built entirely separate from each other and not touching at any place, the transmission of sound is much retarded; and if heavy felt paper or other material is put in between the walls, the partition is made still more nearly soundproof. In order to decrease the thickness of such a wall as much as possible, the "staggered" partition is used, in which there are two sets of studding, one for each side of the wall, but ar ranged alternately instead of in pairs as in the double partition. The arrange ment is shown in plan in Fig. 131. The two walls are entirely separate from each other and the felt paper may be worked in between the studs as shown, or the whole space may be packed full of some soundproof and fireproof material such as mineral wool. There is a so-called "quilting paper" or "sheathing-quilt" manufactured from sea weed, which is much used for this pur pose. The inside edges of the two sets of studs are usually placed on a line, making the whole wall 8 inches thick, where 4-inch studding is used, and the studs may be placed about 16 inches on cen ters in each wall. Each set of studding should be bridged sep arately.
Another case where a double wall may be necessary, is where pipes from heaters or from plumbing fixtures are to be carried in the wall. In case of hot pipes, care must be taken to have the space large enough so that the woodwork will not come dangerously near the pipes.
An important matter in connection with the framing of the partitions is the way in which they are supported; but this involves knowledge of the framing of a floor and, therefore, it will be left for the present. It will be taken up after we have considered the floor framing.